UPS 403 UCU ULTIMATE EPOXY NOVOLAC 75 is a high build solvent free epoxy novolac coating designed to provide outstanding chemical and corrosion protection of steel and concrete structures in continuous immersion conditions at elevated temperatures.
This solvent free coating is easy to mix and apply heated plural feed spray equipment and once applied will cure at room temperature.
UPS 403 UCU has been designed to be applied using heated plural feed spray equipment
Excellent adhesion to correctly prepared surfaces
Excellent erosion resistance – Suitable for use in aqueous slurries
Exceptional chemical resistance against harsh industrial chemicals
Applied in a single coat
Outstanding resistance to abrasion and mechanical damage
Solvent free epoxy novolac – Reducing Health & Safety concerns
Formally known as Chemi-Tech UC / 175 UC
Applications for UPS 403 UCU ULTIMATE EPOXY NOVOLAC 75 include:
Chemical resistant coating for bunds, secondary containments, chemical spill areas, tank plinths etc.,
Protection of pumps, valves fittings etc.,
Chemical drains and channels
Protection of concrete areas subject to aggressive chemicals – Pump bases
Apply by heated plural feed spray
Surface Preparation Manual | Mechanical | Abrasive Blast
Cost Effective Solution
Wet Heat Resistance up to 110°C (230°F)
Useable Life
15 mins @ 20°C (68°F)
Tensile Shear Adhesion
(ASTM D1002 Abrasive Blasted Mild Steel with 75-micron profile)
188KG/cm² (2,650 psi)
Corrosion Resistance
(ASTM B117)
Minimum 5,000 hours
Available Colours
Grey | Red
Minimum Over-Coating Window
4 hours @ 20°C (68°F)
Flexural Strength
(ASTM D790)
480KG/cm² (6,800 psi)
Compressive Strength
(ASTM D695)
592KG/cm² (8,400 psi)
Pack Sizes
1LTR (0.25 US Gallon) | 4LTR (1.1 US Gallon) | 16LTR (4.2 US Gallon)
1LTR (1.25 US Gallon) of fully mixed product will give the following coverage rates -
2.5m² at 400 microns 26ft² at 16 mil
16LTR (4.2 US Gallon) of fully mixed product will give the following coverage rates -
16m² at 1000 microns 171ft² at 40mil
Please note that the coverage rates quoted are theoretical and don't take into consideration the profile or condition of the surface being repaired
Suitable for use in immersed conditions at temperatures up to 110°C (230°F)
Resistant to dry heat up to 170°C (338°F) dependent on load
The product demonstrates resistance to a wide variety of inorganic acids, alkalis’, salts and organic media.
Chemical
(1) Sulphuric Acid
(2) Acetic Acid
(3) Chromic Acid
(4) Hydrobromic Acid
(5) Hydrocholric Acid
(6) Benzene
(7) Phosphoric Acid
(8) Butanol
(9) Nitric Acid
(10) Ammonia Hydroxide
(11) Ethanol
(12) Toluene
(13) Xylene
Concentration
(1) 98%
(2) 10%
(3) 10%
(4) 40%
(5) 36%
(6) 100%
(7) 75%
(8) 100%
(9) 10%
(10) 30%
(11) 100%
(12) 100%
(13) 100%
Temperature
(1) 75°C
(2) 50°C
(3) 75°C
(4) 50°C
(5) 50°C
(6) 60°C
(7) 90°C
(8) 50°C
(9) 50°C
(10) 80°C
(11) 60°C
(12) 60°C
(13) 60°C
If the chemical is not listed, please refer to the Unique Polymer Systems Technical Centre for advice.
Email: sales@uniquepolymersystems.com or call +44 (0) 1531 636 300
