UPS 813 EQS EPOXY QUARTZ SCREED is a solvent free high build epoxy resin repair mortar for use on concrete flooring. The product has been designed to be applied to uneven concrete surfaces at a wet film thickness of 10-30mm (3/8”- 1 1/4”). on curing the product will ensure any imperfections on the surface of the concrete are reduced.
Extremely hard-wearing product
Very high compressive strength –
3 times higher than standard concrete
Can be applied up to a 30mm wet film thickness with no slumping
No shrinkage regardless of thickness applied
Outstanding adhesion properties to metallic and non-metallic surfaces such as: concrete, brick, stone etc.,
Exceptional characteristics for heavy traffic areas
Outstanding chemical resistance to a wide range of industrial chemicals
Solvent free material –
Reduce Health & Safety concerns
Formally known as Grano-Tech
Applications for UPS 813 EQS EPOXY QUARTZ SCREED include:
Repairs to floors, ramps, steps, coving etc.,
Rapid repair of any damage stonework
Bonding and grouting of equipment such as supports, tiles, pump blocks
Repairing damage bund / secondary containment areas
Surface Preparation Manual | Mechanical | Abrasive Blast
Useable Life
25 minutes
Brush or Roller
Applied Primer
Trowel or Squeegee
Applied Mortar
Useable Life
25 mins @ 20°C (68°F)
Hard Dry
Forklift Traffic
48 hours @ 20°C (68°F)
Compressive Strength
(ASTM D695)
880KG/cm² (12,500 psi)
Impact Resistance
(ASTM D256)
1.8 Joules
Available Colours
Grey | Natural
Hard Dry
Foot Traffic
24 hours @ 20°C (68°F)
Direct Pull off Adhesion
(ASTM D4060)
35KG/cm² (500 psi)
Flexural Strength
(ASTM D790)
490KG/cm² (7,000 psi)
Shrinkage
(ASTM C246)
Nil
Pack Sizes
10KG | 45KG
10KG Unit (4.3 LTR / 1.15 US Gallon) of fully mixed material will give the following coverage rates
0.86m² at 5mm 9.25ft² at 0.20”
0.5m² at 5mm 5.35ft² at 0.19”
0.43m² at 10mm 4.6ft² at 0.4”
0.215m² at 20mm 2.3ft² at 0.75”
45KG Unit (18 LTR / 4.75 US Gallon) of fully mixed material will give the following coverage rates
3.6m² at 5mm 38.75ft² at 0.19”
1.8m² at 10mm 19.3ft² at 0.27”
0.9m² at 20mm 9.68ft² at 0.27”
Please note that the coverage rates quoted are theoretical and don't take into consideration the profile or condition of the surface being repaired
Chemical
Sulphuric Acid
Sodium Hydroxide
Hydrochloric Acid
Phosphoric Acid
Diesel
De-ionized Water
Crude Oil
Brine
Concentration
20%
50%
10%
30%
-
-
-
-
Temperature
40°C (104°F)
40°C (104°F)
40°C (104°F)
40°C (104°F)
30°C (86°F)
20°C (68°F)
40°C (104°F)
40°C (104°F)
The product demonstrates resistance to a wide variety of inorganic acids, alkalis’, salts and organic media.
If the chemical is not listed, please refer to the Unique Polymer Systems technical centre for advice
Email: sales@uniquepolymersystems.com or call +44 (0) 1531 636 300
