UPS 814 CRS CHEMICALLY RESISTANT SCREED is a chemically resistant, solvent free epoxy resin repair mortar for use on problematic concrete flooring.
The product has been designed to be applied to uneven concrete surfaces subject to chemical attack from strong industrial chemicals. The material can be applied at a wet film thickness of 10-30mm (3/8 – 1”), on curing the product will resist 98% sulphuric acid, 36% hydrochloric acid and 75% phosphoric acid.
Extremely hard-wearing product
Can be applied up to a 30mm wet film thickness with no slumping
Very high compressive strength -
4 times higher than standard concrete
No shrinkage regardless of thickness applied
Exceptional characteristics for heavy traffic areas
Outstanding chemical resistance to a wide range of industrial chemicals
Solvent free material –
Reduce Health & Safety concerns
Outstanding adhesion properties to metallic and non-metallic surfaces such as: concrete, brick, stone etc.,
Applications for UPS 814 CRS CHEMICALLY RESISTANT SCREED include:
Repairs to floors, ramps, steps, coving etc.,
Refurbishment of chemical boxes
Protection to chemical drains, floors, channels etc.,
Repairing damage bund / secondary containment areas
Surface Preparation Manual | Mechanical | Abrasive Blast
Useable Life
25 minutes
Brush or Roller Applied Primer
Trowel or Squeegee Applied Mortar
Useable Life
25 mins @ 20°C (68°F)
Hard Dry
Forklift Traffic
48 hours @ 20°C (68°F)
Compressive Strength
(ASTM D695)
880KG/cm² (12,500 psi)
Impact Resistance
(ASTM D256)
1.8 Joules
Available Colours
Grey | Natural | Red
Hard Dry
Foot Traffic
24 hours @ 20°C (68°F)
Direct Pull off Adhesion
(ASTM D4060)
35KG/cm² (500 psi)
Flexural Strength
(ASTM D790)
490KG/cm² (7,000 psi)
Shrinkage
(ASTM C246)
Nil
Pack Sizes
30KG
30KG (13.9 LTR / 3.68 US Gallon) of fully mixed material will give the following coverage rates -
2.78m² at 5mm 30ft² at 0.20”
0.5m² at 5mm 5.35ft² at 0.19”
1.39m² at 10mm 14.95ft² at 0.4”
0.695m² at 20mm 7.48ft² at 0.75”
Please note that the coverage rates quoted are theoretical and don't take into consideration the profile or condition of the surface being repaired
Resistant to dry heat in excess of 200°C (392°F) dependent on load.
Chemical
(1) Acetic Acid
(2) Sulphuric Acid
(3) Acetic Acid
(4) Chromic Acid
(5) De-ionised Water
(6) Hydrobromic Acid
(7) Hydrocholric Acid
(8) Benzene
(9) Phosphoric Acid
(10) Steam Out
(11) Butanol
(12) Nitric Acid
(13) Ammonia Hydroxide
(14) Ethanol
(15) Toluene
(16) Xylene
Concentration
(1) 10%
(2) 98%
(3) 10%
(4) 10%
(5) -
(6) 40%
(7) 36%
(8) 100%
(9) 75%
(10) -
(11) 100%
(12) 10%
(13) 30%
(14) 100%
(15) 100%
(16) 100%
Temperature
(1) 30°C (86°F)
(2) 40°C (104°F)
(3) 30°C (86°F)
(4) 40°C (104°F)
(5) 40°C (104°F)
(6) 30°C (86°F)
(7) 35°C (95°F)
(8) 35°C (95°F)
(9) 45°C (113°F)
(10) 180°C (356°F)
(11) 40°C (104°F)
(12) 30°C (86°F)
(13) 45°C (113°F)
(14) 45°C (113°F)
(15) 40°C (104°F)
(16) 40°C (104°F)
The product demonstrates resistance to a wide variety of inorganic acids, alkalis’, salts and organic media.
If the chemical is not listed, please refer to the Unique Polymer Systems technical centre for advice
Email: sales@uniquepolymersystems.com or call +44 (0) 1531 636 300
